Availability: | |
---|---|
Quantity: | |
BL-M7621AX7
LB-LINK
Without BT
MTDIATEK
1T1R
Router:WAN,LAN,I2C,I2S,SPI
Introduction
BL-M7621AX7 is a highly integrated Dual-band WLAN AP module, it build with MT7621DA ,MT7905 and MT7975 .It combines a 2T2R dual-band WLAN subsystem. This module integrates a dual-core MIPS1004Kc(880MHz),HNAT/HQoS/Samba/VPN accelerators,3-port GbE switch, One USB3.0 and 2 UART-port for debug. This module compatible IEEE 802.11 a/b/g/n/ac/ax standard .WLAN 2.4G RF chain with 40MHz bandwidth can support 573Mbps PHY rate. WLAN 5.8G RF chain with 80MHz bandwidth can support 1201Mbps PHY rate.
Operating Frequency: 2.4~2.4835GHz or 5.15~5.85GHz (5.926~7.125Ghz WLAN Band reserved)
WLAN features:
Support Dual-band 2T2R mode with 20/40/80Mhz bandwidth
Support MU-MIMO RX, MU-OFDMA TX/RX
Support TX/RX Beam former
Support DBDC (dual band dual concurrent)
Embedded MIPS1004Kc(880MHz,Dual-core)
32KB I-Cache and 32KB D-Cache per core
256KB L2 Cache(shared by Dual-core)
SMP capable
Single processor operation configurable
Gigabit Switch
3-port with full-line rate
3-port 10/100/1000Mbps MDI transceivers
Embedded DDR3-1200 128MBytes(KGD)
One USB3.0 compatible with USB2.0
HW storage accelerator
HW NAT
2Gbps wired speed
L2 bridge
IPv4 routing ,NAT,NAPT
IPv6 routing ,DS-Lite,6RD,6to4
HW QoS
16 hardware queues to guarantee the min/max bandwidth of each flow
Seamlessly co-work with HW NAT engine
HW Crypto Engine
Deliver 400~500Mbps IPSec throughput
2 UART interface
One system LED, three LAN-port LED, one 2.4GHz wireless LED, one 5.8GHz wireless LED
Block Diagram
General Specifications
Module Name | BL-M7621AX7 |
Chipset | MT7621DA,MT7905DAN,MT7975DN |
WLAN Standard | IEEE 802.11 a/b/g/n/ac/ax |
I/O Interface | Giga Eth PHY/USB3.0 compatible with USB2.0/UART |
Antenna | IPEX connector for external WLAN antenna |
Dimension | 60*53*5.7mm (L*W*H) |
Power Supply | |
Operation Temperature | -10℃ to +50℃ |
Operation Humidity | 10% to 95% RH (Non-Condensing) |
Product Dimension
Module dimension: 60*53*5.7mm(L*W*H; Tolerance: L ±0.15mm;W ±0.15mm;H ±0.3mm)
Package Dimensions
Package specification:
1. 12 modules per blister plate and 144 modules per box.
2. The blister is bound with wire membrane and put into anti-static vacuum bag.
3. Put 1 bag of dry beads (20g) in each anti-static vacuum bag. 1 pcs 3 point humidity card.
4. The outer box size is 35.2*21.5*15.5cm.
Introduction
BL-M7621AX7 is a highly integrated Dual-band WLAN AP module, it build with MT7621DA ,MT7905 and MT7975 .It combines a 2T2R dual-band WLAN subsystem. This module integrates a dual-core MIPS1004Kc(880MHz),HNAT/HQoS/Samba/VPN accelerators,3-port GbE switch, One USB3.0 and 2 UART-port for debug. This module compatible IEEE 802.11 a/b/g/n/ac/ax standard .WLAN 2.4G RF chain with 40MHz bandwidth can support 573Mbps PHY rate. WLAN 5.8G RF chain with 80MHz bandwidth can support 1201Mbps PHY rate.
Operating Frequency: 2.4~2.4835GHz or 5.15~5.85GHz (5.926~7.125Ghz WLAN Band reserved)
WLAN features:
Support Dual-band 2T2R mode with 20/40/80Mhz bandwidth
Support MU-MIMO RX, MU-OFDMA TX/RX
Support TX/RX Beam former
Support DBDC (dual band dual concurrent)
Embedded MIPS1004Kc(880MHz,Dual-core)
32KB I-Cache and 32KB D-Cache per core
256KB L2 Cache(shared by Dual-core)
SMP capable
Single processor operation configurable
Gigabit Switch
3-port with full-line rate
3-port 10/100/1000Mbps MDI transceivers
Embedded DDR3-1200 128MBytes(KGD)
One USB3.0 compatible with USB2.0
HW storage accelerator
HW NAT
2Gbps wired speed
L2 bridge
IPv4 routing ,NAT,NAPT
IPv6 routing ,DS-Lite,6RD,6to4
HW QoS
16 hardware queues to guarantee the min/max bandwidth of each flow
Seamlessly co-work with HW NAT engine
HW Crypto Engine
Deliver 400~500Mbps IPSec throughput
2 UART interface
One system LED, three LAN-port LED, one 2.4GHz wireless LED, one 5.8GHz wireless LED
Block Diagram
General Specifications
Module Name | BL-M7621AX7 |
Chipset | MT7621DA,MT7905DAN,MT7975DN |
WLAN Standard | IEEE 802.11 a/b/g/n/ac/ax |
I/O Interface | Giga Eth PHY/USB3.0 compatible with USB2.0/UART |
Antenna | IPEX connector for external WLAN antenna |
Dimension | 60*53*5.7mm (L*W*H) |
Power Supply | |
Operation Temperature | -10℃ to +50℃ |
Operation Humidity | 10% to 95% RH (Non-Condensing) |
Product Dimension
Module dimension: 60*53*5.7mm(L*W*H; Tolerance: L ±0.15mm;W ±0.15mm;H ±0.3mm)
Package Dimensions
Package specification:
1. 12 modules per blister plate and 144 modules per box.
2. The blister is bound with wire membrane and put into anti-static vacuum bag.
3. Put 1 bag of dry beads (20g) in each anti-static vacuum bag. 1 pcs 3 point humidity card.
4. The outer box size is 35.2*21.5*15.5cm.
content is empty!